Sound Unit for D90 crawler.
SKU:
£35.00
£35.00 - £45.00
Sound Unit for D90 crawlers.
3 versions available.
D90/FX – Engine sound only
D90/SFX – Engine sound, plus extra sound effects like horn, siren. (requires 1 spare radio channel with central point)
D90/SFX+ - As SFX plus volume control from the radio handset (requires 2 spare radio channel with central point)
Features (All Versions)
Engine start sound (automatically starts when throttle of neutral position is detected).
Engine idle sound.
Engine speed up and down to suit throttle position.
Engine stop sound (automatically stops after 10 seconds of no throttle detection).
Powered from servo lead 5v supply. No extra wiring.
Comes complete with speaker.
Comes with servo splitter servo lead, for plug and play to your ESC.
SFX Versions
Horn sound
CB chatter
Siren (police) sound
Fire truck sound
Old police siren
Servo lead for extra radio channel control
SFX+ Version
Volume up
Volume down
Servo lead for extra radio channel control
Instructions can be downloaded here
3 versions available.
D90/FX – Engine sound only
D90/SFX – Engine sound, plus extra sound effects like horn, siren. (requires 1 spare radio channel with central point)
D90/SFX+ - As SFX plus volume control from the radio handset (requires 2 spare radio channel with central point)
Features (All Versions)
Engine start sound (automatically starts when throttle of neutral position is detected).
Engine idle sound.
Engine speed up and down to suit throttle position.
Engine stop sound (automatically stops after 10 seconds of no throttle detection).
Powered from servo lead 5v supply. No extra wiring.
Comes complete with speaker.
Comes with servo splitter servo lead, for plug and play to your ESC.
SFX Versions
Horn sound
CB chatter
Siren (police) sound
Fire truck sound
Old police siren
Servo lead for extra radio channel control
SFX+ Version
Volume up
Volume down
Servo lead for extra radio channel control
Instructions can be downloaded here
Sold Out
You might also like...
TARR Smoke Unit
£2.00 - £24.00
Upgrade smoke unit for Heng Long & Taigen tanks, simple plug and play.
MK1 & MK2 if used with IBU2 systems the smoker is fully proportional.
MK3 Pro & MK4 Pro fully proportional, works with Heng Long, Taigen, Torro, Tamiya tanks and other radio control models with one or two motors
MK1 (12v) comes pre-wired ready for use with IBU3 (1 plug for fan, 1 plug for heater), but even if you not using IBU3 it should be now easier to connect the heater supply cable to your chosen power source.
We now offer a conversion service to convert the MK1 or Mk2 to twin plug connection ready for IBU3's separate heater and proportional fan outputs. Please select this from the below drop down menu and add to basket as well as the TARR unit.
Dimensions (L) x (W) x (H)
MK1 & 3- 55mm x 40mm x 50mm
Mk2 & 4- 55mm x 55mm x 50mm
MK3 & MK4 wiring diagram available here
TARR smokers FAQ
No Smoke
This is not a fault, but because the wick which soaks up the oil has dried out or this is common with new units. Simple put finger on the fan to stop it spinning for 1-2 minutes, in this time the heater will get hot and start to draw the oil up through the wick to the heater to smoke. Reason to stop fan is it allows the heater to get hotter and speed up the process. Once the wick is soaked with oil it is fine and doesn’t need doing again unless the unit runs dry.
What oil and how much
Various oils can be used, but please consider that non-commercial smoke oil maybe toxic and not suitable for use indoors.
Our preference is Megasteam, available from RCTE for UK customers, which works great in the smokers. With the Megasteam the bottle comes with a pipette lid, half to full a pipette is enough and should last 20-60 minutes, depending on use
Connection of wires for proportional units
Instructions (based on Heng Long installation)
1) Plug the 2 pin plug into the MFU smoke output port
2) First pair of red/black cables connects to one motor (red to red, black to black)
3) Second pair of red/black cables connects to other motor (red to red, black to black)
For tank electronics without switched smoker output (Tamiya). Step 1 above, need to remove the 2 pin plug and connect to the battery supply via a switch (not included)
MK1 & MK2 if used with IBU2 systems the smoker is fully proportional.
MK3 Pro & MK4 Pro fully proportional, works with Heng Long, Taigen, Torro, Tamiya tanks and other radio control models with one or two motors
MK1 (12v) comes pre-wired ready for use with IBU3 (1 plug for fan, 1 plug for heater), but even if you not using IBU3 it should be now easier to connect the heater supply cable to your chosen power source.
We now offer a conversion service to convert the MK1 or Mk2 to twin plug connection ready for IBU3's separate heater and proportional fan outputs. Please select this from the below drop down menu and add to basket as well as the TARR unit.
Dimensions (L) x (W) x (H)
MK1 & 3- 55mm x 40mm x 50mm
Mk2 & 4- 55mm x 55mm x 50mm
MK3 & MK4 wiring diagram available here
TARR smokers FAQ
No Smoke
This is not a fault, but because the wick which soaks up the oil has dried out or this is common with new units. Simple put finger on the fan to stop it spinning for 1-2 minutes, in this time the heater will get hot and start to draw the oil up through the wick to the heater to smoke. Reason to stop fan is it allows the heater to get hotter and speed up the process. Once the wick is soaked with oil it is fine and doesn’t need doing again unless the unit runs dry.
What oil and how much
Various oils can be used, but please consider that non-commercial smoke oil maybe toxic and not suitable for use indoors.
Our preference is Megasteam, available from RCTE for UK customers, which works great in the smokers. With the Megasteam the bottle comes with a pipette lid, half to full a pipette is enough and should last 20-60 minutes, depending on use
Connection of wires for proportional units
Instructions (based on Heng Long installation)
1) Plug the 2 pin plug into the MFU smoke output port
2) First pair of red/black cables connects to one motor (red to red, black to black)
3) Second pair of red/black cables connects to other motor (red to red, black to black)
For tank electronics without switched smoker output (Tamiya). Step 1 above, need to remove the 2 pin plug and connect to the battery supply via a switch (not included)
Rotating Effect Orange Beacon - Large
£6.50
Slightly larger beacon, ideal for 1/10 scale models.
5 Modes
1 - Fast rotate
2 - Slow rotate
3 - Slow flash
4 - Fast flash
5 - Off
The beacon plugs into a spare radio channel and to change mode flick switch. Note it can also be used via a 5v max supply and will always default to mode 1 when powered on.
Video
5 Modes
1 - Fast rotate
2 - Slow rotate
3 - Slow flash
4 - Fast flash
5 - Off
The beacon plugs into a spare radio channel and to change mode flick switch. Note it can also be used via a 5v max supply and will always default to mode 1 when powered on.
Video
Rotating Effect Orange Beacon - Large Dome
£6.50
5 Modes
1 - Fast rotate
2 - Slow rotate
3 - Slow flash
4 - Fast flash
5 - Off
The beacon plugs into a spare radio channel and to change mode flick switch. Note it can also be used via a 5v max supply and will always default to mode 1 when powered on.
Suitable for 1/10 or larger scales.