IBU2U Base
SKU:
2007
£125.00
£125.00
per item
IBU2U Specification
Manual Download
* Some of the newer released tanks have revised wiring, if your tank does NOT have a manual volume control you will need one or a RVC unit with the IBU2U.
** PLEASE NOTE THE FOLLOWING WIRING CHANGE MAYBE REQUIRED OR YOU CAN DAMAGE THE IBU2U. IT IS THE USERS RESPONSIBILITY TO CHECK AND CORRECT AS NOT COVERED BY WARRANTY.
Suitable accessories
3D printed case
Speakers
RVC control unit
Basic 6 channel radio set
TARR IBU Edition
- Control via proportional transmitter (4 channels required)
- Plug and play for Heng Long tanks (including the newer 2.4ghz versions) *
- Plug and play for Taigen tanks *
- Taigen airsoft recoil support
- Fully Tamiya compatible IR system (IR code, tank classes, tank slowdown)
- Compatibility with IBU first series repair function to simulate a repair tank (bergepanzer) with IR range limitation via jumper
- Proportional track control (including spinning), with transmitter-switchable momentum linked to tank class
- 20A max per track channel (software limits can be changed), with current monitoring and limitation
(warning flashes on apple LED, if selected) - Improved driver controls
- Track power is enough to drive a HL tank, even on grass or slopes, with stock gearboxes
- Both direction elevation control from transmitter without rewiring
- Headlights and tail lights can be switched on and off by transmitter
- Working brake light (May need alterations to existing wiring if tail lights are shared with headlights)
- All controls (turret, gun, lights, etc.) are available even with engine stopped
- Support for tamiya-style and servo recoil
- Improved servo recoil action (fast return, slowing to a stop)
- Duel smoker ports (1 proportional for fan, 1 switched for heater)
- Proportional control of smoke generator (full power during engine startup, then proportional to engine revs)
- Smoke generator can be switched on/off via remote
- Digitally mixed sound (multiple sounds can be played at once)
- 16bit sounds & 8bit sounds can be used and inter mixed
- Every sound file can have it’s volume adjusted independently to all other sounds
- 15W sound amplifier, with user defined limiter so can use stock 3w speaker
- 3 Engine cold and warm start and stop sounds (randomly played)
- 3 Machine gun sounds (randomly played)
- 3 Main guns sounds (randomly played)
- Engine revving without tank moving
- Li-Po battery support (2S and 3S) with voltage detection and automatic tank shutoff at low battery voltage
- Extended apple LED signalling selectable: end of reload, board bootstrap, warnings (LiPo low voltage, motor over-current,
- overheating)
- Settings via microSD card
- Easy setup with receiver: Follow voice commands
- Super lightweight class. One hit and destroyed!
- Direct plug and play for HL, Taigen, Tamiya and Vampire IR systems
- English instructions (PDF)
- True scale speed adjustment
- Proportional super spin power down to off
- Track recoil effect.
- Limited reverse speed
- 5 Pin plug support for xenon flash unit, with airsoft micro-switch input
- Support for up to 16Gb capacity microSD cards
- MicroSD card now easier access on top of IBU2U
- Expansion port for future modules
- User can update firmware themselves
- User can pay to unlock all the Full Option features
Manual Download
* Some of the newer released tanks have revised wiring, if your tank does NOT have a manual volume control you will need one or a RVC unit with the IBU2U.
** PLEASE NOTE THE FOLLOWING WIRING CHANGE MAYBE REQUIRED OR YOU CAN DAMAGE THE IBU2U. IT IS THE USERS RESPONSIBILITY TO CHECK AND CORRECT AS NOT COVERED BY WARRANTY.
Suitable accessories
3D printed case
Speakers
RVC control unit
Basic 6 channel radio set
TARR IBU Edition
1 available
Suitable accessories
IBU2U (Ultimate) Case
£5.00
3D Printed case for IBU2U
Complete opening for removal and insertion of the microSD card.
Note
These are printed to order so please allow a few more additional days before dispatch.
Colour may vary
IBU2U not included
Complete opening for removal and insertion of the microSD card.
Note
These are printed to order so please allow a few more additional days before dispatch.
Colour may vary
IBU2U not included
3D Printed speaker box (Medium)
£12.00 - £22.00
3D Printed speaker box for Visaton FR7 and FRS7 Speakers.
(See below for short video comparison of speakers out and in the box)
Dimensions -
66mm Long
66mm Wide
35mm High (with speaker)
Available with or without speaker.
3DP Box Pack contains
3D Printed box
4 x fixing screws
3DP Box & Speaker Pack contains
3D Printed box
4 x fixing screws
Visaton FR7 or FRS7 Speaker (Installed)
2 Pin plug and lead (soldered to speaker)
Note
May contain sharp edges
No instructions provided
These are printed to order so please allow a few more additional days before dispatch
Colour may vary
RCTE reserve the right to revise or remove the product without notice
(See below for short video comparison of speakers out and in the box)
Dimensions -
66mm Long
66mm Wide
35mm High (with speaker)
Available with or without speaker.
3DP Box Pack contains
3D Printed box
4 x fixing screws
3DP Box & Speaker Pack contains
3D Printed box
4 x fixing screws
Visaton FR7 or FRS7 Speaker (Installed)
2 Pin plug and lead (soldered to speaker)
Note
May contain sharp edges
No instructions provided
These are printed to order so please allow a few more additional days before dispatch
Colour may vary
RCTE reserve the right to revise or remove the product without notice
NEW Servo Recoil
£15.00
3D Printed servo recoil unit.
Designed to replace the Heng Long recoil unit or airsoft unit (with modification) and retain use of the Heng Long elevation unit.
Now with 3 different size servo gears to allow small, medium and large recoil distance. See videos below.
Approximate travel distance.
small = 10mm
medium = 15mm
large = 20mm
Pack contains
Recoil body
Recoil slider
Servo gear x 3
Micro servo
Note
Some modification maybe required
No instructions provided
These are printed to order so please allow a few more additional days before dispatch.
Colour may vary
Designed to replace the Heng Long recoil unit or airsoft unit (with modification) and retain use of the Heng Long elevation unit.
Now with 3 different size servo gears to allow small, medium and large recoil distance. See videos below.
Approximate travel distance.
small = 10mm
medium = 15mm
large = 20mm
Pack contains
Recoil body
Recoil slider
Servo gear x 3
Micro servo
Note
Some modification maybe required
No instructions provided
These are printed to order so please allow a few more additional days before dispatch.
Colour may vary
TARR IBU edition
£24.00
Sold out
Upgrade smoke unit for specifically for the IBU2U and IBU3 control boards.
Also suitable for Elmod Fusion,Clark TK60, Heng Long 6.0 & 6.1 systems.
Simple plug and play. One plug for heater (SMR) and one plug for fan (SMP)
Dimensions (L) x (W) x (H)
55mm x 40mm x 50mm (Metal)
55mm x 55mm x 50mm (Plastic)
Piranha 2020 Battle Unit C/W wiring
£30.00
Sold out
Piranha 2020 now has bigger and brighter hit indicators!!!
Piranha, is a complete plug in IR battle unit by RCTA.
Piranha features the latest SMD technology IR receivers it is not only one of the smallest battle units available but also possibly the best for IR performance.
Piranha features 4 X IR receiver modules each with built-in IR noise filters capable of receiving IR signals over a 45 metre (147 ft) distance , 4 x high intensity red side mount LEDs and a high power, narrow angle IR emitter. The Piranha assembly comprises two interconnecting PCBs, a base unit and receiver/emitter unit. The standard base unit for Piranha is a 5+2 pin base for connection to RCTA, IBU & Tamiya units. An optional 5 pin base is available for direct connection to the new El Mod Fusion series.
If using a Heng Long or Taigen MFU then a MAKO is recommended as the MAKO will not only provide for LED indication but also a compatible pin output.
A 3D printed cover is available here
IBU RVC Remote volume control
£25.00
Sold out
The RVC module replaces the physical volume potentiometer, allowing to remote adjust the audio level using a spare receiver channel. A standard proportional radio (AM, FM, or 2.4 GHz) which provides servo PPM outputs can be used.
Specification
The RVC is a small board (approx. 1 inch x ½ inch) and is simply plugged between volume potentiometer connector of IBU2 or TPA and a spare receiver channel.
Setup
Connect the servo-like lead to you receiver, typically the 6th channel has a control knob which will act in a familiar way for regulation.
Turn ON the power to receiver by the main power switch for the IBU2, leaving the transmitter OFF
You now should see a green light steady ON
With the control knob set to minimum. Turn ON the transmitter, the green light should start to blink slowly
Increase the knob position to maximum, the green light should blink faster (according to knob position)
Now you can connect the other 3 pin plug cable to Volume Pot connector on IBU2 or TPA
Turn ON the IBU2 and make it play a sound and set the volume to desired level
Specification
The RVC is a small board (approx. 1 inch x ½ inch) and is simply plugged between volume potentiometer connector of IBU2 or TPA and a spare receiver channel.
Setup
Connect the servo-like lead to you receiver, typically the 6th channel has a control knob which will act in a familiar way for regulation.
Turn ON the power to receiver by the main power switch for the IBU2, leaving the transmitter OFF
You now should see a green light steady ON
With the control knob set to minimum. Turn ON the transmitter, the green light should start to blink slowly
Increase the knob position to maximum, the green light should blink faster (according to knob position)
Now you can connect the other 3 pin plug cable to Volume Pot connector on IBU2 or TPA
Turn ON the IBU2 and make it play a sound and set the volume to desired level